Product introduction
Arduino DS Robot WiFi Video Car Robot is an education and teaching robot kit based on the Arduino UNO R3 main controller and Robot-Link WiFi wire less video transmission module.
1.Use the phone, computer and other terminals, controlled by wireless WiFi
2.The robot can capture video data, and real-time transmission to control software.
3.Provided with the source code, you can carry out secondary development learning.
4.IO interface of the robot is completely open and can be easily extended to the sensor.
5.compatible with Arduino IDE, the use of graphical or code form of prog-ramming software, low degree of difficulty,Suitable for entry-level game players.
(XiaoR GEEK) Robots-Store “www.robots-store.com” provides a large num ber of robot application source code and tutorials, you can learn more robot programm-ing and development knowledge. (XiaoR GEEK) Robot Forum: www.wifi-robots.com provides a technical discussion place for maker.
Packing List
Step of usage
FAQ
1: Turn on the switch, you can search for the robot's wireless signal, but can not be connected or can not be a stable connection.
Solution: Please get the robot fully charged before trying to control.
2: Turn on the switch, the robot's WiFi module LED lights have been flashing non-stop.
Solution: 1) Electrifying moment, fast continuous press Reset WiFi module.until the module's LED lights flash quickly. Use RJ45 cable to connect the WiFi module and PC, thePC's local IP isset to 192.168.1.3 play Open the PC command prompt window,execute the command telnet 192.168.1.1; and then execute the command firstboot;and power-o f restart.
Solution: 2) If the first step does not work, please contact customer service assistance toresolve
3:Open the PC control client software, prompted the need to install. Net framework components.
Solution:Baidu or Google keyword ". Net framework download" to find the system prompts frame-work version, download and install it.
4:PC client software can not control the robot, mobile phone or Pad client can be controled.
Solution: 1), Turn of the PC firewall
Solution: 2), Remove the PC's RJ45 cable, and restart the computer.
Solution: 3), Using another computer for comparison.
5:Search the robot's signal, it can display the robot's video, but the PC client software and themobile phone Client software are unable to control the robot.
Solution: 1) Check the rear of the MICRO USB (non-side serial pins) jumper cap pin position to ensure that two jumper caps are installed.
Solution: 2), Replace the USB data cable.
Solution: 3), The above steps do not work with the browser login 192.168.1.1 WIFI module man-agement interface (password admin), find the system classification, in the classification of a factory reset button (perform reset), the implementation of a recovery Factory settings.
Solution: 4), If you can not control, please observe the switch on the main board, the blue LED lights flashing about 30 seconds, if not flashing, please re-burn the main control program.
6:You can control the robot, but the directions are disorder.
Solution: In the setting page of the control software, replace the opposite action
instruc-tions,and save.
7:There is no problem with the video, option WiFi mode selection of PC control soft-ware, the software pop-up error warning prompt box .
Solution: 1), Turn of the computer firewall, restart the car and software, waiting for
about 30 seconds, the WiFi module system initialization completed after the
connection.
Solution: 2), Use the browser login 192.168.1.1WiFi module management interface, the WiFi module to restore a factory settings (see question 5).
8: Electricity or mechanical arm to head stuck in the position, the abnormal noises.
Solution: Disconnect all servos or camera cradle(PTZ), then refer to the tutorial: one by one to access the servos, adjust the appropriate angle of each servo in turn,and lock the current appropriate angle.
9:PC client select WiFi mode, there is no warning tips, but can not control the car, mobile client can control.
Solution: 1), Use the browser login 192.168.1.1WIFI module management interface, the WIFI module to restore a factory settings (see question 5).
Solution: 2), If the first step is still not working, it may be the MicroUSB interface loose, resulting in data can not be transmitted through the USB data wire to the main control board, then the TTL serial port pin with the DuPont line in the WiFi module on the other side,the WiFi module RXD and the main control board TX is connected, TXD and the main control board RX Connected,GND connected to the main control board GND. If still can not be controlled, Exchange the con-nection position of the TX and RX(two DuPont line).
10: The camera back to the video is not clear enough: manually rotate the camera
ens,adjust the focal length
11: Camera without image, the robot can control
Solution: 1), Check if the camera's USB interface is connected
Solution:2), The camera connected to the computer, try QQ video chat, verify the
camerais intact, such as the computer can not be used, please contact customer
service repla-cement camera.
12: The ef ective control of the robot is very close (less than 2 meters)
Solution: 1), Check if the antenna is loose, please tighten.
Solution: 2), Avoid the use of many wireless routers in the surrounding environment.
Solution: 3), Use the browser to log in the management interface of the 192.168.1.1 WiFi module, in the "Wifi" classification, the default channel 11 switch to 1 or 3, and save settings
13: Manual control mode is normal, patrol escape or other automatic mode robot motion disorder.
Solution: 1), According to the tutorial, check carefully if the sensor wiring is correct, and if the sensitivity adjustment is correct.
Solution:2), In the line vault or other automatic mode, the robot should be the
overall performance of the forward state, respectively, to observe the left and right
side of the motor rotation direction, and the side of the motor on the side of the line change position,so that the vehicle was forward state, And then refer to "Problem 6" to adjust the robot direction in manual mode.
14: After making contact , the robot move around regularly, out of control.
Solution: Let the car run 15S, it will automatically exit the test mode; if not, please
contact customer service.
15: Secondary development, the robot can not be controlled to download the master program.
Solution: 1), Remove the USB data wire connected to the main control board.
Solution: 2), Reduce the baud rate of the burning software.
Solution: 3), Replace the burning tool ardware or computer.
16: USB connection is correct, turn on the switch,the WiFi module LED light does
not bright, and the wireless signal cannot be found.
Solution: Check the WiFi module R68 silk screen at the resistance of the external
forceis knocked of , if you have to touch please contact customer service